48 F1 exhaust
My truck has 350 sbc with block hugger headers, I want to put in a dual scavanger exhaust system. I've been looking in the catalogs at the systems, but I have no idea on what to buy. I want to do it...
View Article350 TBI first time rebuilding engine...question
Hi:D How you doing guys? I decide to rebuild my 350 TBI engine for 1993 In real... I jut need your help friends:rolleyes: I took a stuck engine and want to turn it to performance engine I over size the...
View ArticleIntake Leak Into Lifter Valley???
Manifold has been off a few times, and every time, the gasket "crush" appears to be all around. But I'm consistently oil fouling the same three plugs. Clean them and again, the same three! Engine runs...
View ArticleComputer controlled HEI engine with adjustable advance?
This site says it can be done.... Eliminate the factory ECM, wire it into this stand alone: G4 Storm : Cost effective engine management you can rely on. : EngineLogics.com
View Articleengine thoughts....
ok so im about to do a new top end on my 383.... heres what i am taking off factory 76 cc chamber cast iron heads 8.5:1 compression edelbrock performer intake 600cfm holley (single pumper) heres what...
View ArticleDistributor Fit Question
I am installing an HEI in my 327 Chevy. I bought the engine unassembled. It came with an Edelbrock aluminum intake. I bought a new HEI and when I fit it in, I notice that there maybe 1/8" side to side...
View ArticleNitrous cams ?
Talking small blocks here... What is the main difference that seperates them from others... n/a cams vs nitrous cams. Valve events, lsa, ivc/evc, lift etc... Are there any off the shelf cams that can...
View ArticleClik here to view.
Ford 460 holley 750 Questions :)
I'll just make 1 thread and keep updating it with questions rather then posting a new one each time i need help. I have just brought myself a 1970 jaguar with a ford 460 bigblock running a holley 750...
View Articlehi or low compression??
do i guess right to think a 119cc head would raise the compression on my 454 BBC. currently i run 148 heads with 122cc but i have pretty tall dome piston. given i use the same gasket for both heads.
View ArticleVacuum Question
I have a small block Chevy with a demon carb. I Have the vacuum tank hose, trans modulator hose and brake booster hose going to a connector screwed into the back of the manifold. Idle is a little...
View ArticleWhy do i get poor gas mileage
:confused:I have a 51 ford f1 with a 302 & aod & the original 3:73 rear I have an old holley 4 bbl on it-right now i am only getting 10-12 mpg I thought that I should be getting better gas...
View Article1989 SBC Valve Stem Seals
I've got a 1989 SBC with a one cylinder fouling the plug and using oil but does not smoke. The engine has been rebuilt and runs great, don't know how many miles are on it. It takes 800-1000 miles for...
View ArticleZZ4 camshaft
I have a 305 tbi 91 and a guy offered my a zz4 camshaft and i was wanting to know if i can use it in my 305. What kind of upgrade would it offer in hp and torque. Just to say he wants $40 and said he...
View ArticleClik here to view.
electric power steering to my mustang 1967 eleanor build
hi all . been a while . am nearly finished on my eleanor mustang . just got the electric power steeing up and running. its great and i think you all could use it for some ideas. awsome bit of kit !!
View Article1984 350 C10 Silverado electric choke
Can someone tell me how the electric choke works? The light stays on and its obvious that the choke isn't working. I have one wire coming off of the carb at what seems to be the adjuster. Where is that...
View ArticleBBC hyd roller cam help
I have a .30 454 with forged domes 29.7cc and am running stock 781's so comp should be 9:5-1 , also picked up some comp cams retro hyd roller lifters for a song and dance in the box so looking for a...
View Articlemanifolds
I[m about to buy a new manifold and the thing is i can buy a HOLLEY STRIP DOMINATOR 300 . 25 for about 100$ and the thing is they don't have the water ports in the back of the manifold by the distrib...
View ArticleBlower back fire.
I am having a problem with my 426 cube inch motor . the motor has a bds blower systems with two 650 carters on top . W hat is going on is at an idle the motor run fine . Once I drive the car on the...
View ArticleMopar crank shaft question
I am new to the Mopar world and will need all the help I can get. I have a 413 engine with the long ram manifold that I will install in a 31 Plymouth 5 window coupe. My question is what do I have to...
View Article94 s15 build
have 86 454 fron 1 ton truck and 87 350 from 1/2 ton truck. either one any good to build
View Article