302 camshafts
I don't do Fords much and just recently found that Ford changed the cam grind for the 302 cu in to the Windsor grind and firing order. Took me SEVERAL tries at timing my newly rebuilt engine before...
View Article305
can anyone tell me why someone would run a 350 head gasket on a 305? My first thought was to lower compression, and I never heared it run. I have used a set of 350 heads on a 305 and it ran good,still...
View Article383 LT1 cam suggestion/recommendations
Hey fellas I wanted to pick you all's brains a little :thumbup: I recently built a 383 LT1 TPI for a customer of mine and he wants to be more street than strip. He is looking for speed in a second gen...
View ArticleSBC 350 New Engine Trouble
98 Chevy K1500 5.7 350 vortec .30 over comp cams 08-300-8 (grind cs 262h-r12) duration at .050 206(intake) and 210(exhaust) Recent engine and Trans Overhaul Finally got the timing figured out on this...
View Article305 ho cam
im trying to decide on a cam 305 bored .40 over flat tops, ported 416 (ho) heads edelbrock performer intake, geting a 650 edelbrock carb not sure if its to much carb but geting it cheap so gonna try...
View Article305 mess
i have a 305 that a guy built for a street stock and the only thing i did to it was put new valve seats and springs and retainers on it .it has a 460 lift solid lifter cam ,not sure about duration and...
View Article750 downleg or 650 straight leg on a SBC 350
which carb would run better. 750 DP downleg booster or 650DP with straight leg booster. 350 sbc roller cam, 227@50, .565 lift on 108LSA, vortec heads with 180 intake runner, eddy air gap RPM. 1 3/4 LT...
View ArticleHow to find piston CC? I have measurments
I would like to know how to find what the CC of this dished piston is. Says the dish is 0.080in deep and 3.020in in diameter. Can anyone help me out here? I did try contacting the manufacturer but they...
View ArticleHarmonic balancer size question
I'm going to have to get another harmonic balancer, I been using a 6 3/4 in. balancer on my sbc internally balanced. The outer ring is moving towards the timing cover. I don't know if this has anything...
View Article350 chevy ID
I just purchased what is said to be a 1984 corvette short block. The block is standard bore but the piston tops are flat with a wide two valve relief? I thought most small blocks of that era were...
View ArticleClik here to view.
Glass packs in the collectors
I've just pulled the mufflers out of the collectors to see how they look. Of course I have no idea how they should look. They seem pretty burned at one end (the engine end) and fine at the other. I've...
View Articledisassebled sbc help
i got my uncle a great running 350cid 260 hp marine engine to build for a 69 nova he was going to build. he got the rolling car built and then disassembled the engine with intentions on 400 hp. at that...
View ArticleGen I SBC Stamped rockers to roller rocker questions.
Hey, I build a stout 383 and put some 1.6 ratio stamped rockers on it (whoops) and one rocker arm split last night and left me on the road side. I'm planning on switching to a roller rocker with a...
View ArticleRadiator Leak Sealer Recommendation
I'm not sure if this is the correct forum for radiator post but here it is. I have a radiator with a leak in a spot I can't solder so I am soliciting suggestions for a really good metal repair epoxy...
View ArticleClik here to view.
Holley Hi-Tek Air Cleaner VS Spectre Dual Cold Air Intake
Is there a big Difference between these two Air Cleaners?? Attached Thumbnails
View Article327 or 350 ???
i have a motor i bought the casting is 3932388 by the casting it says its a 350 from 1969 the suffix code on the head deck of the block reads T0221HV T= totwanda ny, 02= feb , 21= day hv= 1965 vette...
View ArticleTbi top end vs ls swap
I've been planning my ls swap for my car but I'm having second thougbts because of costs, plus I need to get the car drivable before summer. So I had the idea of swapping the heads and intake from a...
View Articletiming cover
I have a 97 roller cam sbc 4 bolt motor, i will soon start building, it nas the plastic cover on the timing chain. it says on it to replace it if removed. why is this. should i get the oe unit or...
View Article1980 gmc 1 ton flywheel
it has 292 but want put early years 283 in it so what flywheel do i use for the v8.. can i use any v8 flywheel on this ? tranny 2 wheel sm456 4 speed with low any help would be grate thanks
View ArticleWhat's the correct temperature
I have a 350 crate engine I'm trying to put electric fans. Now I put a cooling fan switch but my question is what temperature should they come on. Thanks for any info I can get all this is in a 85 el...
View Article