Isky 264 Mega for this combo
Thinking about this HFT camshaft for a mild 355 in a '72 Chevelle. Dart ss 165 iron heads with 72cc chambers 6cc flat top pistons 9.3:1 CR Weiand 8125 dual plane manifold Quadrajet carb TH350 2.73 axle...
View ArticleFuel pump question
What size fuel lines are the pressure ratings of fuel pumps based on? I need 6psi with 1/2" fuel lines for a recent sbc 383 build. Thanks for the help.
View Article327
I just dynoed my 327 and came out with 300 rwhp and 360 ftlbs with 6 pounds of boost through a weiand 177. The motor is bored 30 over 9-1 compression ported double hump 64 cc heads, comp 292 h cam and...
View ArticleSBC Oil Pump Pick Up Clerance
I have a 327 SBC. How much clearance do I need from the oil pump pick up screen and the bottom of the oil pan. I have about 1/4". Is that enough. Thanks for any reply's
View Article383 Mopar build, looking for parts sources
I'm a Mopar guy from way back,Even though I like every muscle car made in the U.S.A. and have run them all! Been checking prices on parts for a 66 Fury 383 ci 330 hp build. Prices for parts if...
View Article2 Different heads on same motor?
I just received my 350 engine today and noticed that they have two differnt head casting numbers on it. 14096219 and 14102191 I did a little research and found out the 219 head has 1.94/1.50 64 cc and...
View Article327 sbc build 68 nova
Hey guess brand new member. I have a 68 nova with full manual race built th-350 and ford 9 inch 4.10 gears. I used to want big power(young and dumb) now I just want a street rig and maybe a run at the...
View ArticleAutolite 4100
I just got 6 autolite 4100 4v carburetors.Most are complete and some are missing some small parts.But i think i have enough parts to end up with 2 maybe 3 good rebuilt carbs.I went to a few local parts...
View Articlea 355 can do the same thing as a 383?
I have read many hotrod magazines, read through forums and seen so many people post HP and TQ numbers of what 355's can put out identical power or close to it... Well the torque was down some but......
View ArticlePushrod wear
Last summer I built a 357 sbc with a hydraulic flat tappet cam, hardened pushrods, and aluminum full roller rockers. I had problems with the no.2 intake rocker coming out of adjustment. After three...
View Articlefalse guide replacement
I have the equipment to install bronze guide liners and have done it for years with no problems. However, now I have a collection of heads that have had the orginal guides drilled out and replaced with...
View ArticleThe Legendary 396 BB
Has anybody ever owned one of these engines? A big block with a short stroke mustve been something.... i ran across one and thought to myself, maybe i should buy it... would you buy one if you could...
View ArticleClik here to view.
Intake Manifold Replacement (Valve Cover(s) clearance)
I'm replacing my old cracked edelbrock intake manifold with a new edelbrock performer series on my sbc. The new intake must be a little wider, but not by much, it almost fits under the valve covers. I...
View Articleblown sbc price question??
Hello. Wat you think a fresh bored 030 over 350....steel crank n rods....forged pistons....new bearings......blower cam....miloden water pump...hi volume oil pump and chrome pan.....dbl roller timing...
View Articlemileage on a flathead
I have a flathead it is my first one I would love to know how many miles it has on it. anyone out there no how many miles they have on one,be interesting to see who could come up with the most miles...
View Article355 chevy whats next
im looking at a 85 monte carlo and im looking to make it mine in everyway thats why i have posts in alot of areas. sorry. but it a 355 chevy with a 510 cam lift and headers, intake, exhaust, heads and...
View ArticleNewbie with head questions
Ok hello my first post here except to introduce myself please dont be to hard,,i have a 92 trans am and it has a 5.7 crate engine with vortecs on it,,and i got my hands on a 74 corvette 350 rebuilt...
View ArticleClik here to view.
Help with Push Rod Length SBC
Trying to dial in my push rod length. Using the Comp Cams checker 8.150" gauge centers the wear pattern best, however the wear pattern seems pretty wide. Almost from 1/3 inboard to 1/3 outboard. Also...
View ArticleEdelbrook heads
has any one used the Edelbrook 60979 E-tec 170 aluminum heads in a votec head swap?
View Article