where can I buy one cam bearing?
I need a cam bearing for a sbc, just one. Any ideas where I can buy a single one?
View Articletimng
having problem wth getting initial timing right now i have 22 to 24 degrees is that to much i have a 454 compcam 527 lift 292 - 312 brand new msd street fire dist. trying to figure out do ineed to do...
View ArticleVibration in Drive train/ Chev 350/ Turbo 400
Hello, So I have a vibration in my 1985 chev 350/Turbo 400. I had the vibration before I replaced the engine (tired) and it's still there. I rebuilt the trans with a new torque converter, vibration...
View ArticleClik here to view.
Storing engine
Hi Guys Just got my engine back from the rebuilder and now I need to store it for a while.When I say awhile, probably around a year maybe a little more.Whats the best way to do this.The engine is...
View ArticleCircle Track 406 top end questions
New rules for our track came out and have opened up our rules greatly. We run a 3/8 mile ASPHALT oval street stock weighing 3000 lb, turning 6800-7000 every night. SBC 406...the question I have is on...
View ArticleQuadrajet Issues
Hello everyone this is my first post here on the forum and I have several questions about a quadrajet carb. I have a '79 chevy with a 350 in it. With a 4 bbl carb ontop of it. The engine has been...
View ArticleRocker contacting top of retainer on vortec heads
I don't mean to beat a dead horse, but here's my dilemma. I thought I had this ALL figured out. I've got the #906 vortec heads, Comp 26918 springs(recommended installed height 1.80") 787 retainers and...
View ArticleCarb issues w/BB Chevy w/BDS blower
Hi. hope someone is willing to help. I'm having trouble with the idle on my ride. It's a '69 El Camino with a 468 and it has a BDS 8-series blower with two Holly DP's. I live in Ft. Lauderdale and am...
View ArticleLS Serpentine Belt Help
I need to use an after-market Serpentine belt system for clearances. 2008 Pontiac G8 L76 engine in itself is perfect for what I need, but it has VVT (Variable Valve Timing) which I would like to keep....
View Article406 small block review
Okay guys, im new to this board but have often come here when i am in search of engine help, so i finally decided to join. Heres the deal, im building a 406 small block that will go in a truck (yea its...
View ArticleEdelbrock Performer rebuild
I'm about to soak the bottom half in Napa carb cleaner that comes in a gallon can. Wasn't planning on removing the throttle shafts and primary plates. Did remove the secondary plates as they are not...
View ArticleIs this cam ok with 416 heads?
So I got a 305 with 416 heads for cheap (yes I know a 305, it's a mud truck so it's not getting a lot if $$ in it). With it I got a new cam, lifters, stock rockers, timing chain and flex plate and...
View ArticleClik here to view.
Help Identify who remanufactured 302 engine
I took my 302 out to repair a leaking freeze plug. Actually, the prior owner replaced the plug with a rubber expansion plug. I found what appears to be a tag from when it was remanufactured. Anyone...
View Article327 small block
I have a 327 engine with casting #3782870. I know its a 327 with horsepower range from 250 to 375. I can't find anything on the suffix code. It came out of a 62 Chevy truck. Don't know if it was...
View ArticleExhaust and engine accoustics for asthetics and performance
This is all in relation to a 90 degree v8 I am looking for the highest frequency/note/tone/pitch I can get. I very much enjoy the higher, crisper, cleaner sound the european v8 makes. I hate with a...
View ArticleCarb bog vs timing issues?
Ok. It's a performance built .040 350 SBC, custom built Pro Systems 4150, MSD Pro billet and 6AL, Blaster 2 coil. Timing started at 35 degrees total at 3000. Pro Systems carb has a slight bog spot...
View ArticleWork at home with your liberty reserve account
MAKE UNLIMITED CASH WITH YOUR LIBERTY RESERVE AND PERFECT MONEY ACCOUNTS DAILY! This is absolutely free and very easy, all you need is an internet facility.... I have been using this system for some...
View ArticleFabricating Aluminum Intake Manifold, need help
Hello all and Happy Holidays. I have a stroked Volvo B20 engine that I am building and will be turbocharging and I am looking into fabbing a new intake manifold out of aluminum, yes I do weld aluminum....
View Articletorque spec
i have a '77 chevy 350 V8 and wanted to know if anyone knows the torque spec for the exhaust manifold to block. the chilton's book i have doesn't have it for my V8, but the I6 spec says 25 ft/lbs. Can...
View Article383 stroker assembly
Alright guys, all the pieces and parts have arrived and I am ready to start the mock up assembly of my 383 to make the required clearances. I need some advice on the details.. Can somebody please break...
View Article