A Valve Spring In Slow Motion.
Makes you appreciate what these little springs have to go through.
View ArticleFuel pressure monkey business, 96' Silverado
K1500 305. Went out to start her after sitting for 2 days, and crank, crank, sputter, and die. She trys but wont start. So I gave up till today. I put the fuel pressure gauge on it, and hit the key and...
View ArticleClik here to view.
Found under vavle cover
Pulled my valve covers to set the valves and found this laying next to a valve spring. Been about 2000 miles since I set the valves (solids) so it was time. Looks big enough to at least block an oil...
View ArticleMechanical Fuel Injection
Hi, I am thinking of using mechanical injection on the street. I'm thinking a 6-71 with a birdcatcher hat, it would be on a mopar 440. What I'm conserned with is cylinder wash and oil getting dilluted....
View Article92 silverado engine upgrades
i just purchased a second silverado 350 tbi with the nv4500 trans ( might be a 3500) i always get it mixed up my other silverado is the same except it has a tbi to tpi swap on it im going to use this...
View ArticleIdentify Lunati Camshaft
could you identify #139536 on rear of camshaft front of camshaft has RRB 292-302 F4JH
View ArticleNeed guidance
Hi guys I'm a new guy into gas engines I was a diesel junkie for years and want to try something new. I have a 71 gmc with a 350 that I want to put power into sadly it's a 2 bolt main. I'm haven...
View Articlecanadian 2 barrel intake any one answer question on it
So I bought a 59 chevy pu with what I'm assuming to be a 307 or 327 has a Canadian intake I was reading that it has no egr stuff and less likely to have vacuum leaks is there more to it and would...
View ArticleStraight pipe
Would it hurt to run the motor straight pipes...Ive always heard it would hurt the valves and this that and the other
View Articleoil leak
I have a oil leak on my 1984 Chevy Silverado I am not sure if it is the valve covers or the rear seal I have oil on my bell housing on my transmission I have already replaced the valve cover gaskets...
View Article1995 gmc vortec head swap what TBI & spacer to use
1995 gmc truck edelbrock heads GM Preformance intake 12496821 edelbrock cam 3702. what holly 670 TBI and airaid spacer should I use?
View Article383 Stroker with blow by PCV problem
Bought a C10 with a 383 installed. It had a blow by problem with the oil breather/catch can installed. PCV was removed and capped. I installed a PCV connected to air filter and blow by problem still...
View ArticleSpark plugs problem on vortec heads
Hello! I have a strange problem I was changing plugs on my 355 when I Noticed that nr 5 cyl plug was wet and all others were fine. Any got a idea of what causes this? She burns no coolant and no white...
View Articleholley street avenger problem
Hey all, new to the site. sorry if i'm posting wrong or wrong place, but i need help. 1987 chevy V10 4x4 350. originally tbi, just rebuilt engine, using orig. intank fuel pump, return style reg.,...
View ArticleCamel hump heads vs vortec heads
Hello to all i got a question for you guys, i want to change the heads on my 1972 327 or its a 350 i got to pull pan but havent got that far yet to verify the motor,if you had a choice to go camel hump...
View ArticleWhat effects does low rpm's have on air fuel mixture?
(preface: 355sbc, 232@.50 480lift cam, decent heads, rpm air gap, holley 650 dp, t5 manual) I put a wideband gauge in my Camaro and I've been having fun fine tuning this carb with it. Got it dialed...
View ArticleWeird Oil Leak
I have a rebuilt SB 350 that I did myself a while back. Was using 20-50W oil and never had a leak. I just changed my oil 2 weeks ago to a little bit thinner oil and now I keep having an oil leak...
View ArticleK-line Ind
Did K-line ind. go out of business. Thier website doesn't work anymore and the only site that seems to work is any Ebay clearence store. Does this mean the Bronze -Bullet guide liners left are NOS?
View ArticleChevy Water Neck Bolts Leaking
Whenever I go above 6000 rpm lately, coolant has been shooting up out of my water neck like a fountain. I had a billet aluminum swivel neck with o-ring on a Super Victor intake. I added a gasket to see...
View Articlechoosing cam for mild 355?
I was looking for help choosing a cam for a mild 355 motor in a heavy c10 truck, as Its abundntly clean I can't do it haha. Motor is a 355 with a set of 195 runner, 64cc heads, rpm intake, 3.73 gears,...
View Article