LT 1 Timing cover
Can the timing cover #12552426 Stamp# 1021416 be subed for #12552427 stamp #1255032, if you are NOT using a crank trigger senso
View ArticleCamshaft Suggestions
Boy I know camshafts there's only a million inputs needed to make a decent suggestion, then a million different brands and grinds. Basic engine is a Gen 1 350. I would love to set it up for a roller...
View Articleon my way to race and have MAJOR ISSUE HELP
Okay I hooked uo my mangnafuel 300 pump and aeromotive regulators last night got done at 5 am didn have the tee I needed to test it. I put the tee on this morning turned it on and fuel pressure guages...
View Article350 piston question?
I have a 350 out of a 1977 chevy truck with the 76cc smog heads and was wondering if these came with flat top, dome, or dished pistons. I am planing on going to vortec heads in the spring so i really...
View ArticleJust another cam choice thread
I'm building a budget 355 out of all my spare parts from past builds to put in my '40 chev coupe, specs as follows: Dana 60, 4.11 gears, 3spd manual, probably in the 3000lbs range. 4 bolt 355, 10.5:1...
View ArticleAir filter versus cold air intake
My engine runs a little bit warm. I do live in Arizona and the 100 plus degree temperatures do not help. I am running a 383 and I am trying to cool the engine down a little. I am installing a cowl...
View Article383 long rod
how is the 383 long rod combo made without have a offset ground crankshaft made?
View Articletrack results unhappy
track prep was excellent 1987 camaro coupe 350 stock bottem end rebuilt trickflow 195's 62 cc heads with 28 thous gaskets calculated at 9.9 to 1 comp cams 280h with 1.6 roller rockers (shifted at 6200...
View ArticleOil feed hole in Roller Lifters
I am installing a roller cam in my 383 SBC. I have never used a hydraulic roller cam. Do the oil feed holes need to face in a certain direction? I am pretty sure that it is not critical. They are the...
View ArticleGM TBI mods
Has anyone used SPR Preformance TBI Parts before? I am thinking about sending my stock GMC TBI unit to them and get it reworked for my vortec head swap. I am curently useing a holly 670 and I hate this...
View ArticleClik here to view.
where to put it (the Engine)
i just bought a 31 ford rat rod, that has a 4x2 tube frame there is 19 3/4 " between the rails. It has a narrowed ford 9" in the back and a mustang 2 front clip on it with rack and pinion. it had a 350...
View Articleh-pipe after mufflers?
I'm currently running header mufflers that side exit in front of the rear wheels. I've read the benefits of adding a balance pipe to a dual exhaust system. Since my mufflers basically bolt to the...
View ArticleQuestions about heads for 383 stroker
I am a rookie when it comes to putting an engine together. I have a 350 sbc (already .030 over, 3.75 crank) looking to make a 383 stroker dirt track engine. I have a set of World Products S/R I-052...
View ArticleWhat size carb to run?
I have a 408 sbc and wanted to know what size carb I should run. I can get a good deal on a holley 650 but don't know if ill be better getting a holley 750. rpm max will be 6000. I wont be racing just...
View ArticleOil pressure
I'm having some hesitation problem when accelerating from stop. My oil pressure is very low at idle could that be the reason why. Motor is '64 chevy 350
View ArticleClik here to view.
Speed Pro 7070 P orientation
Hello Everyone, I've finally decided to finish off my 355sbc. I have a set of Speed Pro 7070p .30 pistons for it. How do i know the correct orientation for the piston . Should it be as picture here,...
View ArticleEdelbrock Carb Secondaries Bog
I bought a remanufactured Edelbrock Thunder AVS 650 CFM carb from Summit Racing. The motor is a mildly built 350 with about 2000 miles. Runs great except any time I give enough throttle for the...
View Article1966 nova l79 carburetor
I have a 1966 L79 nova that I want to put the original holley model 3145 585 cfm carburetor back on. I need to know the original springs/clips needed for the carburetor accelerator linkage and where I...
View ArticleClik here to view.
What SBC heads are these?
I might be getting a Set of heads for real cheap, the guy said he thinks they are Pro Action heads but I can't find them. They are stock Vortec style I believe. He says they are 1.94 heads, iron, 64cc....
View ArticleClik here to view.
Chevy 350 Oil Filter/Adapter
Would anyone know what gasket goes onto the pic l posted? I used paint and highlighted the gasket l need. Any help would be much appreciated. 350 Chevy Vortec Oil Filter Cooling Housing Adapter with...
View Article