New Start up...350 efi timing help??
I have a 5.7 350 vortec .30 over comp cams 08-300-8 (grind cs 262h-r12) duration at .050 206(intake) and 210(exhaust) I have gotten the motor installed back in the truck. Long story short... I have...
View ArticleAir/Fuel Problem??? I Think
Hey guys when I drive my truck and hit the gas it wants to sputter and then it drives fine. It does this no matter if Im moving at any speed or if Im stopped and try to go. Always when I hit the gas it...
View ArticleNeed some assistance from the Ford Gurus
Recently picked up an 84 Ford Bronco. Factory emissisions tag shoes 5.0 as does the VIN I've run numbers on the engine and heres what i found INTAKE- D1AE-9425-DA CYLINDER HEAD(VALVE COVER REMOVED)-...
View Article225 slant 6, mopar?
Does anyone have a picture of the motor mts for 225 slant 6, 1969 Dart? Also where to purchase? Thanks Dana
View ArticleFour winns Liberator
Hello I'm getting ready to install a B&M 144 supercharger on a 211 four winns Liberator that has a 350 sbc 260 hp, any tips? I've been running the supercharger on an old hot rod that I've own for...
View Article383 stroker seized
I have a 1981 El Camino with a mild 383. I have been having issues with the carb (600cfm Holly) perculating and the engine makes a ticking sound when accelerating or under load. Well the other day i...
View ArticleIs it ok to sit rebuilt Eng/Tran on tires
I want to bolt my newly rebuild engine and transmission together and install them as one. In the meantime, I was wondering if it is ok, after I bolt them together, to sit them on tires. I have seen...
View Articlemarine 383 hi torque
what parts will i need to use to build hi torque 383 stroker marine motor
View Articlespeed pro forged pistons?
Any one have any experience with these pistons and nitrous? Thinking about throwing them in a budget daily driver 350 and spraying a 200 shot on it.
View ArticlePontiac 400 Q-Jet Idles Too Fast
Like the title says it idles too fast around 1100-1400 rpm, trans in neutral. Fast idle cam off, q-jet has tower drips. All vacuum lines have been disconnected and plugged at the source. I believe this...
View Articlevortec heads on 400 sbc
Ok im thinking about vortec heads on my 400 I was just wondering what I would all have to change I know the intake and can some one give me some ideas on one of those to plz the motor is stock not...
View Article1969 Ford 390 ticking @ 1200 RPM
I have a 66' F100, 390 FE. The engine develops a "ticking" sound above 1200 rpm, it is not an exhaust leak, and I have replaced the four lifters on the passenger side rear two cylinders where the noise...
View Articlegot crank ground but what size?
The mains measure from 2.631-2.636 and the rod 2.095-2.104. The rods seem std but are they?and the mains seem to be. 020?
View Article383?
Have a 350, want a 383. Do I need to bore it .03 over or is that a 400? From my experience a 383 is a 350 with a different crank(essentially) without any boring of the cylinders. Just need some...
View ArticleCam selection
Ok so if you were following my last thread i was building a 350 for nitrous. Ive since abandoned that and am building a 383 all motor. Im planning on these heads: Assault Racing Complete SBC Small...
View ArticlePontiac 350 zero decking?
I don't want to buy a 400. I want to reach 400 pounds of torque with a street cam(5200 rpm) in a 1969 Pontiac 350. Do I really need to zero deck the block to help get to 400 pound of torque? I mean...
View Article302 ford intake manifold
I have stock rebuilt ford 302 in my 55 willys truck,Im currently using the summit 600cfm 4 barrel carburetor and a cast iron 4 barrel intake manifold.I love the way the truck runs,But the engine has...
View ArticleGasket Sealing
Alright, I'm finaly rebuilding my Pontiac 400. New Edelbrock heads from Butler, roller cam, RPM intake. I am getting the gaskets from Butler as well. What do you guys use for sealing off the water...
View ArticleNeed help asap
Hey guys I'm new to this Site and have a major problem need help asap I just had a motor built for my mud truck ill give some brief specs on it maybe it'll help u answer my question its a 400 block...
View ArticleSBC fuel pump push rod stuck ?
Hey guys I'm new to this Site and have a major problem need help asap I just had a motor built for my mud truck ill give some brief specs on it maybe it'll help u answer my question its a 400 block...
View Article