1982 cutlass 307 idle issue
does anybody know what a 1982 cutlass 307 is suppost to idle at?
View ArticleSmall base circle cam or not?
Hi! Every body... As i said before, i'm on a 406 sbc project. I don't know if i need or not a small base circle cam. My interest is on the Hydraulic Roller Voodoo Retro-Fit Lunati 20120711K (60111). It...
View Articleheaders help
i have a 327 in a 85 chevy c10 and i need some help. my tranny cross member is in the way on the passenger side. the cross member is the original one and the headers fit great with engine but i cant...
View ArticleClik here to view.
Rocker Issue!! *** Happened?
New engine build. Brand new 1.65 Scorpion Rockers #10002527 and 7.900" Procomp pushrods #PC7802. Maybe 45 minutes of run time. Mostly idle and one 5 mile round road trip. Went to put in my new push...
View ArticleClik here to view.
sleeving this block
guys i dont much about sleeving blocks, used to be a bad thing but now im sure sleeves have improved... can this one cylinder in this 350 block be sleeved or to much damage? it had a piston break from...
View ArticleSolid lifters on a hydraulic roller.......
This has been discussed around various forums, but Ive never gone with it. Thinking about trying it though..... using AFR comp. ported 195's on a small block with a CompCams hyd. roller. These heads...
View ArticleClik here to view.
Getting to around 396cid using 880 block
To expand on my other thread about using a 400SBC with a roller cam in an L31 Vortec 350 application. What is the best way to get to around 396 cubic inches in a GEN 1 SBC? Anyone know of any good...
View Article12554290 heads on a gen 1 SBC?
I am picking up a set of 12554290 heads from a 1994-96 LT1. Will I have any issues with these going on a gen 1 010 type block? Are these a good choice? I'm getting them dirt cheap. Is the reverse...
View Article68 Firebird Motor Mounts
I have a 68 Pontiac Firebird with a Pontiac 400, Edelbrock heads, and a hyd. roller cam. I ordered a set of motor mounts from Autozone and the bolt hole is not deep enough. I have to add 2 washers to...
View ArticleGMC 6 cyl engine interchange
Does anyone know if the Chevy/GMC 6 cyl engines 250 Ci or 302 CI will bolt to the 4 speed transmission of a 1959 GMC 1/2 ton pickup currently with a 235 in it?
View Articlet b i problems
hey guys, went to take off runners and there is one threaded rod on the bottom holding them on.how can I get at it? also what is the difference between 85-89 and90-92 runners.are they interchangeable?...
View Article73 el camino ss header review
Mild built 350. Want mid length ceramic headers. Found Patriot Clippsters at summit for 322.95. Not familar with this brand. #H8021-1 How about some reviews. Thanks!!!
View ArticleBlack sooty spark plugs
Hello, I know that black sooty spark plugs means you have a rich condition but I need some direction as to what may be causing that and how to fix. I have just put in a new carb (quickfuel ss 680 as...
View ArticleIs my set up going to be ok
Hi there, new to this forum. I have an 85 350 4 bolt with tbi 193 heads-65cc. 345np .030 pistons, knock off duel plane intake,long tube headers and 600 edlebrok carb I have a brand new summit 1102 cam...
View Articlefuel pump pickup an fittings
I am upgrading the fuel tank in my 1986 olds cutlass with a tank from a buick gn. I am putting an intank electric pump in. I am running a new 3/8" feed and return and was thinking about having two -6...
View Article350 engine glass bowl having vapor lock issue
my 350 engine edelbrock carb gas bowl is getting vapor lock what can cause this please help
View ArticleHyd roller lifters in oil for 2 years
I just finished my 364ci build. (.030 350 with a 3.562 stroke crank.) Any how, I used a cam and lifters I had from a previous build that was never used.... 2 years ago, when I recieved the new cam and...
View ArticleClik here to view.
Piston pin looks to far off center.. 454 build might need more compression ??
Gen 6 454 roller block. .030 over flat top pistons -5cc and .004 below deck stock crank .030/.030 stock rods ZZ502 cam Bowtie heads 98cc chamber Bowtie intake. This motor started off as a truck motor...
View Articlecable brackets for sbc
hey guys, need some help with my project car, my 1971 nova with the original 350 2 barrel/th350 transmission... what im working on is i put an edelbrock performer manifold on with a holley 4160 carb,...
View Article